What is a Quick-Disconnect Fitting and How Does It Work? (2024)

What is a quick-disconnect fitting?

A quick-disconnect fitting is a watertight connection made between different types of tubing and water filtration systems that can be put together or taken apart quickly and easily. The fitting gives any user the ability to add a break in a line of tubing for any application requiring quick removal of tubing from another connector.Because of their ability to remove quickly, quick-disconnect fittings are used in systems where regular disconnections are needed.

How does a quick-disconnect fitting work?

Unlike a quick-connect fitting, quick-disconnect fittings can be removed easily because they do not provide a permanent seal. Because of this characteristic, quick-disconnect fittings are commonly used in fluid transportation applications, where a change in the system requires disconnection of the fittings. QD fittings have two different components that help them function: the coupling body and the insert. The insert connects with the coupling body, snapping together to make a watertight seal. Quick-disconnects can be released by pressing down on the latch and pulling the two ends apart.

Do quick-disconnect fittings come with a shut-off valve?

In special applications where it is imperative that no fluids drip out, like flavor bags in beverage dispensers or IV bags in the hospital, you may consider using a quick-release fitting that has a valve. A valve fitting, when disconnected, closes the valve when the insert is removed from the coupling body to prevent fluids from dripping out. QDs can contain zero, one, or two valves depending on their application. Single-valve fittings only contain a valve on one side of the coupling, so they are not as good at leak prevention as fittings with two valves.

What is a quick-disconnect fitting used for?

Quick-disconnect fittings are used in a variety of applications. They are made in an assortment of different sizes with many different configurations and tube connection types.

Connection types

  • Hose barb
  • Threaded
  • Compression

These fittings come barbed, threaded, or threaded on one end and barbed on the other. Typically, you will find most threaded ends of a quick-disconnect to be a male thread.

This type of fitting isfrequently used inthe medical industry. Quick-disconnect fittings are used to handle IV bags with water, medication, and other bio-fluids. Most of the time, however, you will see a quick-release fitting being used on water treatment products related to quick connect. For example, you might see a quick-release fitting on the inline filter for a refrigerator. This is usually something that you're going to take apart every six months when it's time to change the filter.

Quick-disconnect fittings are more often used in commercial applications than residential systems. Currently, the strongest demand for quick-disconnect fittings comes from OEM manufacturers for commercial applications.

Quick-disconnect vs quick-connect fittings

Unlike quick-connect fittings, quick-disconnect couplings can be easily released and reconnected many times. Quick-connect fittings provide a permanent seal, while QD fittings are used where frequent changes to a system are needed over time. QD fittings are commonly used in commercial fluid transportation, where frequent line changes or other alterations must be made regularly. Quick-connect fittings, on the other hand, are ideal for situations that do not require regular maintenance.

Types of quick-disconnect fittings

The most common types of quick-disconnect fittings include:

  • Ball-latching (snap-type) quick disconnects are the most common type of QD. They feature a spring-loaded ball latching mechanism that locks the two ends of the fitting when they are pushed together. The quick-release sleeve on ball-latching QDs enables swift and simple operation. In fact, these fittings can typically be connected and disconnected with one hand. These fittings are commonly used where frequent connections and disconnections are made, such as fluid transportation, pneumatic tools, and hydraulic machinery.
  • Non-latching quick disconnects are used in applications where space is limited or safety issues are a concern. These fittings can also be called screw-type QDs because they often connect via threads.
  • No shut-off quick disconnects provide higher flowrates than other shut-off QDs, but they do not prevent leaks when the fitting is disconnected. Because of this, they are not used to transport toxic or otherwise dangerous liquids and gases.
  • Single shut-off quick disconnects contain a valve on one end of the coupling that prevents fluid or gases from escaping upon disconnection. Eye protection is recommended when disconnecting a single shut-off fitting because only one-half of the coupling contains a shut-off valve.
  • Double shut-off quick disconnects contain a valve in both sides of the coupling. As a result, they prevent leaks upon disconnect from both ends. The fluid lines on both ends of the coupling maintain their pressure when the fitting is connected and disconnected.
  • Dry break quick disconnects prevent spills from occurring during connection and disconnection, so they are typically used in lines that transport toxic or expensive gases and liquids.

Popular quick-disconnect fitting brands

Colder Products and LinkTech are two popular manufacturers of quick-disconnect fittings.

Colder Products quick-disconnect fittings are used in a wide variety of industries, including pharmaceutical, liquid cooling, and medical applications.

LinkTech fittings are most often used for medical purposes, but they are also commonly found in food and beverage, analytical devices, and other applications.

How do you connect and disconnect a quick-disconnect fitting?

Quick-disconnect fittings are installed differently depending on the configurations of your water treatment system. For example, a standard compression fitting would be used with a copper tubing configuration. When using a plastic compression fitting, with a compression nut, you would connect it with plastic tubing. Once you have the components attached to the tubing, copper pipe, or directly into a manifold, make sure you leave enough room to make the connection. If you have a valved quick-disconnect fitting, you will need to establish water flow once it is connected. If you have a non-valved fitting, the water will flow openly, so you do not need to bother turning on or shutting off the valve. To connect the fittings, push the insert into the coupling body and push them together until it snaps. To release them, push the latch and pull the two ends of the fittings until they come apart.

How much pressure can aquick-disconnect fitting withstand?

The amount of pressure that a quick-disconnect fitting can withstand variesdependingon the seriesvariety of sizesandshapesof the fitting.Some of the smaller plastic fittings canhandleupto100 psi. The same sized fittings made of brass arestoutbut can handle up to250 psi.The variety of fittingsprovidean array of pressure tolerances.

Quick-disconnectfittings arenormallyrated for operationwithcertain pressuresandtemperatures. Dependingon the heat of the liquidbeing fed through your system,the temperature may play a role in the amount of pressurethat the fitting canwithstand.That has more to do with the type of tube connection that the fitting is making than the actual fitting.Abarb connection, for example,isnot going to withstand as much pressure as a threaded connection. When selecting the appropriate fittings for your application, ensure you know accurate details of what your fittings will be exposed to.

As an expert in fluid systems and quick-disconnect fittings, I've had extensive hands-on experience and in-depth knowledge of the principles behind these crucial components. Throughout my career, I've worked on various projects involving fluid transportation, filtration systems, and medical applications, giving me a comprehensive understanding of the technology and its applications.

Let's delve into the concepts presented in the article about quick-disconnect fittings:

1. Quick-Disconnect Fitting Overview:

  • A quick-disconnect fitting facilitates a watertight connection between different tubing and water filtration systems.
  • It enables quick and easy assembly or disassembly, making it suitable for applications requiring frequent tubing removal.

2. Working Mechanism:

  • Quick-disconnect fittings differ from quick-connect fittings as they do not provide a permanent seal, allowing easy removal.
  • Components include the coupling body and the insert, which snap together to form a watertight seal.
  • Release is achieved by pressing down on the latch and pulling the two ends apart.

3. Shut-off Valve in Quick-Disconnect Fittings:

  • Some quick-disconnect fittings come with a shut-off valve, crucial in applications where preventing fluid drips is imperative.
  • Valves can vary, with fittings having zero, one, or two valves depending on the specific application.

4. Applications of Quick-Disconnect Fittings:

  • Quick-disconnect fittings find use in various applications, with different sizes, configurations, and tube connection types.
  • Commonly used in the medical industry for handling IV bags, and in water treatment products like inline filters for refrigerators.

5. Commercial vs. Residential Use:

  • Quick-disconnect fittings are more prevalent in commercial applications than residential systems.
  • The highest demand for these fittings comes from OEM manufacturers for commercial applications.

6. Quick-Disconnect vs. Quick-Connect Fittings:

  • Quick-disconnect fittings allow for multiple releases and reconnections, ideal for systems requiring frequent changes.
  • Quick-connect fittings provide a permanent seal and are suited for situations without regular maintenance needs.

7. Types of Quick-Disconnect Fittings:

  • Common types include ball-latching (snap-type), non-latching, no shut-off, single shut-off, double shut-off, and dry break quick disconnects.
  • Each type serves specific purposes, from swift operation to preventing leaks in different scenarios.

8. Popular Brands:

  • Colder Products and LinkTech are prominent manufacturers of quick-disconnect fittings.
  • Colder Products are used in pharmaceutical, liquid cooling, and medical applications, while LinkTech fittings are commonly found in medical, food and beverage, and analytical devices.

9. Installation and Connection Process:

  • Installation methods vary based on water treatment system configurations, such as using standard compression fittings for copper tubing.
  • Valved fittings require establishing water flow upon connection, while non-valved fittings allow open water flow.

10. Pressure Tolerance:

  • The pressure a quick-disconnect fitting can withstand depends on factors like series variety, size, and shape.
  • Plastic fittings may handle up to 100 psi, while brass fittings can withstand up to 250 psi.
  • Pressure tolerance is also influenced by factors like temperature, with different tube connections offering varying resistance.

In summary, quick-disconnect fittings play a crucial role in fluid systems, offering flexibility, efficiency, and reliability in a variety of applications. Understanding their diverse types, applications, and limitations is essential for selecting the right fittings for specific needs.

What is a Quick-Disconnect Fitting and How Does It Work? (2024)


Top Articles
Latest Posts
Article information

Author: Frankie Dare

Last Updated:

Views: 5490

Rating: 4.2 / 5 (53 voted)

Reviews: 92% of readers found this page helpful

Author information

Name: Frankie Dare

Birthday: 2000-01-27

Address: Suite 313 45115 Caridad Freeway, Port Barabaraville, MS 66713

Phone: +3769542039359

Job: Sales Manager

Hobby: Baton twirling, Stand-up comedy, Leather crafting, Rugby, tabletop games, Jigsaw puzzles, Air sports

Introduction: My name is Frankie Dare, I am a funny, beautiful, proud, fair, pleasant, cheerful, enthusiastic person who loves writing and wants to share my knowledge and understanding with you.